Tub and Wall Sealing Caulk Strip Wall and Corner Self Adhesive Peel and Caulk Strip Fixture Tape Caulk Sealer Tub Surround Waterproof Decorative Sealer Trim Pack of 2 (Grey)
Tub and Wall Sealing Caulk Strip Wall and Corner Self Adhesive Peel and Caulk Strip Fixture Tape Caulk Sealer Tub Surround Waterproof Decorative Sealer Trim Pack of 2 (Grey) by TopWoot at Bad Manner Sent. Hurry! Limited time offer. Offer valid only while supplies last. Features:Keep your corner cleanStop dust, bugs and oil from getting inside your hidden wall corner. Keeps your wall corner easy to clean. Provide a
Features:Keep your corner clean
Stop dust, bugs and oil from getting inside your hidden wall corner. Keeps your wall corner easy to clean. Provide a healthier kitchen to your familyFlexible Design
Made with high quality PE material. Pre-shaped for fast and easy. Simply peel and press self-adhesive strip to the surface in minutes. No tools, no mess, hassle and waste, easy alternative to regular caulkMulti-function
This item could be used on different places. Use it on the kitchen desk to avoid oil. Or use it in bathtub to keep your wall corner dry. Provides a long lasting seal and gives a finished professional look to kitchen and bath areas. Keep your house clean and tidy as new one for a long time
1. Please completely clean the surface and make sure it is dry, remove any existing silicone caulking prior to installation.
2. Measure the length of the area to be sealed to determine the correct length and cut the strips accordingly.
3. Take out the strip, measure the same length as the area and mark on the strip with the pencil, then cut it.
4. Peel off 5cm of the adhesive tape from the back of the product and fold into 90 degrees, and then put the strip on the place where you need to seal, keep peeling the tapes until you finish the installation.
5. Cut the butt joint side into 45 degrees when the product needs to be pasted in a 90 degrees corner.
6. Room temperature around 25 Celtigarde for the best, if the temperature is too low, use hair dryer to heat up the paste before sealing for better sticking.
7. While installing, press firmly over the length of caulk strip to ensure a tight seal.
8. Keep the area dry for at least 24 hours for the better effect.
Features & Highlights
- MATERIAL: PVC, waterproof, anti-mildew, acid and caustic Corrosion-resistant, heat resistant, environmentally friendly and non-toxic
- FLEXIBLE DESIGN: Adhered to any angle and surface to form a tight seal and bring you a finished professional look. Keep your house clean and tidy as a new one for a long time.
- EASY INSTALLATION: Simply peel off and press the self-adhesive tape to the surface. No tools, no confusion, no trouble and save time
- WIDE APPLICATIONS: Great for kitchen countertop seams, kitchen sink, bathroom basin and sink, toilet, bathtub, gas stove seams
- 100% CUSTOMER SATISFACTION GUARANTEE: Do not hesitate to contact with us for replacement or refund if not satisfied with the products bought.
|Item Weight:||0.88 pounds|
|Package Weight:||0.93 pounds|
|Package Size:||3.35 x 2.99 x 2.99 inches|
Have questions about this item, or would like to inquire about a custom or bulk order?
If you have any questions about this product by TopWoot, contact us by completing and submitting the form below. If you are looking for a specif part number, please include it with your message.
Related Best Sellers
mpn: 1395391, ean: 0079340815018,
Loctite Epoxy Quick Set is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond in 5 minutes for most projects.Bonds metal, glass, cer...
By System Three
mpn: 1010K10, ean: 0646697100687,
Quick Cure 15 will allow for additional working time over our "five minute" Quick Cure 5. Mix at a 1:1 by volume ratio. Quick Cure is ideal for all small jobs requiring a strong bond and rapid cure. Quick Cure is highly water resistant but not waterp...
mpn: 03333, ean: 0079340033337,
Loctite Speed bonder 312 amber one-part acrylic adhesive is compatible with ceramic, glass and metal materials with a 24 hr. cure time. Delivers great performance with a shear strength of 2490 psi. Maximum operating temperature is +250 F. Perfect for...
By MG Chemicals
mpn: 419C-340G, ean: 0779008419335,
419C Acrylic Conformal Coating is an IPC 830 certified, fast drying, xylene and toluene free product that provides an excellent finish. It is easy to use and does not require special or costly equipment to apply. It is ideal for high moisture environ...
By 3M Scotch-Weld
mpn: 56659, ean: 0021200566592,
3M Scotch-Weld Epoxy Adhesive 2216 is a flexible, two-part epoxy adhesive that cures at room temperature. It provides a high strength bond with both high shear and peel strength while remaining highly flexible, making it ideal for applications where ...
By Clearcast 7050
mpn: 7050-48, ean: 0682962234626,
A Cycloaliphatic based epoxy system designed for the casting and coating of wood, metals, plastics, concrete, fiberglass, kevlar, stone, tile and concrete. 2:1 mix ratio, low viscosity, and a fast cure make this epoxy a candidate for all applications...
mpn: 230-31500, ean: 0687927956353,
PlexusMA310 is a two-part methacrylate (MMA) adhesive designed for structural bonding of thermoplastic, metal, and composite assemblies. Plexus MA310 replaces an older popular Devcon formula Plastic Welder 2 (14340). It is the same formula inside, bu...
By ELLSWORTH ADHESIVES
id=ctl00_ctl00_ContentPlaceHolder1_MainContentArea_DescriptionLabel class=content>One-part, translucent, moisture RTV, moderate flow, UL and Mil Spec, contains UV indicator. 90ml (3 oz.) tube...
By Old Timer Industries LLC.
This epoxy kit is a Cycloaliphatic based epoxy system. Perfect for coating, casting, and sealing all applications. This product can be used on wood, plastics, fiberglass, metals, stones, pebbles, and foam. This can be used in industrial applications ...
By MG Chemicals
mpn: 4223-55ML, ean: 0779008422359,
Ideal for extreme chemical conditions. Urethane conformal coating is a durable finish product that provides a protective coating for printed circuit boards against moisture, corrosion, and thermal shock. It protects and insulates electrical and elect...